Real Exam Questions NSE7_OTS-6.4 Dumps Exam Questions in here [Apr-2022]
Get Latest Apr-2022 Conduct effective penetration tests using NSE7_OTS-6.4
NEW QUESTION 18
You are investigating a series of incidents that occurred in the OT network over past 24 hours in FortiSIEM.
Which three FortiSIEM options can you use to investigate these incidents? (Choose three.)
- A. Overview
- B. Risk
- C. List
- D. Security
- E. IPS
Answer: A,B,C
NEW QUESTION 19
When device profiling rules are enabled, which devices connected on the network are evaluated by the device profiling rules?
- A. Known trusted devices, each time they change location
- B. All connected devices, each time they connect
- C. Rogue devices, only when they connect for the first time
- D. Rogue devices, each time they connect
Answer: C
NEW QUESTION 20
Refer to the exhibit, which shows a non-protected OT environment.
An administrator needs to implement proper protection on the OT network.
Which three steps should an administrator take to protect the OT network? (Choose three.)
- A. Deploy an edge FortiGate between the internet and an OT network as a one-arm sniffer.
- B. Deploy a FortiGate device within each ICS network.
- C. Use segmentation
- D. Configure firewall policies with industrial protocol sensors
- E. Configure firewall policies with web filter to protect the different ICS networks.
Answer: A,D,E
NEW QUESTION 21
Which three common breach points can be found in a typical OT environment? (Choose three.)
- A. Hard hat
- B. Global hat
- C. Black hat
- D. VLAN exploits
- E. RTU exploits
Answer: C,D,E
NEW QUESTION 22
An OT network architect needs to secure control area zones with a single network access policy to provision devices to any number of different networks.
On which device can this be accomplished?
- A. FortiNAC
- B. FortiGate
- C. FortiSwitch
- D. FortiEDR
Answer: A
NEW QUESTION 23
Refer to the exhibit and analyze the output.
Which statement about the output is true?
- A. This is a sample of a FortiAnalyzer system interface event log.
- B. This is a sample of a PAM event type.
- C. This is a sample of an SNMP temperature control event log.
- D. This is a sample of FortiGate interface statistics.
Answer: A
NEW QUESTION 24
In a wireless network integration, how does FortiNAC obtain connecting MAC address information?
- A. MAC notification traps
- B. Link traps
- C. RADIUS
- D. End station traffic monitoring
Answer: C
NEW QUESTION 25
Refer to the exhibit.
You are navigating through FortiSIEM in an OT network.
How do you view information presented in the exhibit and what does the FortiGate device security status tell you?
- A. In the widget dashboard and there are one or more high-severity incidents for the FortiGate device.
- B. In the business service dashboard and there are one or more high-severity security incidents for the FortiGate device.
- C. In the PCI logging dashboard and there are one or more high-severity security incidents for the FortiGate device.
- D. In the summary dashboard and there are one or more high-severity security incidents for the FortiGate device.
Answer: D
NEW QUESTION 26
Refer to the exhibit.
Based on the topology designed by the OT architect, which two statements about implementing OT security are true? (Choose two.)
- A. IT and OT networks are separated by segmentation.
- B. Micro-segmentation can be achieved only by replacing FortiGate-3 and FortiGate-4 with a pair of FortiSwitch devices.
- C. FortiGate-3 and FortiGate-4 devices must be in a transparent mode.
- D. Firewall policies should be configured on FortiGate-3 and FortiGate-4 with industrial protocol sensors.
Answer: A,C
NEW QUESTION 27
An OT network architect must deploy a solution to protect fuel pumps in an industrial remote network. All the fuel pumps must be closely monitored from the corporate network for any temperature fluctuations.
How can the OT network architect achieve this goal?
- A. Configure a fuel server on the remote network, and deploy a FortiSIEM with a single pattern temperature performance rule on the corporate network.
- B. Configure a fuel server on the remote network, and deploy a FortiSIEM with a single pattern temperature security rule on the corporate network.
- C. Configure both fuel server and FortiSIEM with a single-pattern temperature performance rule on the corporate network.
- D. Configure a fuel server on the corporate network, and deploy a FortiSIEM with a single pattern temperature performance rule on the remote network.
Answer: D
NEW QUESTION 28
Refer to the exhibit.
An OT administrator ran a report to identify device inventory in an OT network.
Based on the report results, which report was run?
- A. A FortiSIEM analytics report
- B. A FortiSIEM CMDB report
- C. A FortiAnalyzer device report
- D. A FortiSIEM incident report
Answer: B
NEW QUESTION 29
What are two benefits of a Nozomi integration with FortiNAC? (Choose two.)
- A. Importation and classification of hosts
- B. Direct VLAN assignment
- C. Adapter consolidation for multi-adapter hosts
- D. Enhanced point of connection details
Answer: B,D
NEW QUESTION 30
An OT administrator is defining an incident notification policy using FortiSIEM and would like to configure the system with a notification policy. If an incident occurs, the administrator would like to be able to intervene and block an IP address or disable a user in Active Directory from FortiSIEM.
Which step must the administrator take to achieve this task?
- A. Create a notification policy and define a script/remediation on FortiSIEM.
- B. Define a script/remediation on FortiManager and enable a notification rule on FortiSIEM.
- C. Deploy a mitigation script on Active Directory and create a notification policy on FortiSIEM.
- D. Configure a fabric connector with a notification policy on FortiSIEM to connect with FortiGate.
Answer: B
NEW QUESTION 31
An OT administrator configured and ran a default application risk and control report in FortiAnalyzer to learn more about the key application crossing the network. However, the report output is empty despite the fact that some related real-time and historical logs are visible in the FortiAnalyzer.
What are two possible reasons why the report output was empty? (Choose two.)
- A. The administrator selected the wrong logs to be indexed in FortiAnalyzer.
- B. The administrator selected the wrong time period for the report.
- C. The administrator selected the wrong devices in the Devices section.
- D. The administrator selected the wrong hcache table for the report.
Answer: B,D
NEW QUESTION 32
......
Authentic Best resources for NSE7_OTS-6.4 Online Practice Exam: https://prepaway.testkingpdf.com/NSE7_OTS-6.4-testking-pdf-torrent.html
